Replacing a gas furnace usually costs $3,800 – $8,500 installed for a standard 80,000 BTU model. Electric furnaces cost less to install, while high-efficiency, propane and oil furnaces cost more, up to about $13,000 for a large oil system.
Use the furnace replacement cost calculator below to price your own furnace by fuel, home size, climate and efficiency. Every table and example on this page uses the same formula.
Furnace Replacement Cost Calculator
Estimated furnace cost
$3,800 – $8,500
Typical: $6,100
Using national average prices. Add your zip code for local prices.
- Furnace size80,000 BTU
- New furnace, installed$3,700 – $8,200
- Permit$100 – $300
- Size is a rule-of-thumb estimate. Ask for a Manual J load calculation before you buy.
Sorry, we couldn't calculate that. Please check your answers, or reload the page.
Compare quotes from local heating contractors
Free, with no obligation. Local, pre-screened pros will contact you to confirm your project and give you a price.
Thanks! Your request is in. Local pros will contact you shortly, usually within a business day, to talk about your project.
Check your quote
We compare it with the estimate for your answers above and your zip code.
Estimates are a guide. Prices vary with your home and local conditions.
Got more than one quote? Compare them side by side →
Questions to ask
Red flags
Share your price
Tell us what you were quoted or paid. We use it, anonymously, to check and improve our estimates. It uses your answers above, so change them there if you need to.
Thank you. Your price helps other homeowners.
Estimates are a guide. Prices vary with your home and local conditions.
What drives the cost of a new furnace
A furnace replacement includes the new unit, connecting it to your ducts, gas or oil line and venting, a new filter rack where needed, startup testing and haul-away of the old furnace. The calculator uses a fixed amount by fuel plus an amount for every 1,000 BTU of heating output, then adds the cost of a high-efficiency model if you choose one.
Fuel
| Fuel | 80,000 BTU furnace, standard, installed | Typical |
|---|---|---|
| Electric | $2,200 – $5,800 | $4,000 |
| Natural gas | $3,800 – $8,500 | $6,100 |
| Propane | $4,000 – $9,400 | $6,700 |
| Oil | $6,700 – $10,600 | $8,600 |
Electric furnaces are cheapest to buy and install but usually the most expensive to run. Gas is the most common choice where it is available. Oil and propane systems cost more to install and may need a new tank, which can add $600 to $2,500.
Home size and climate (BTU)
Furnace output is measured in BTU per hour. The calculator multiplies your living area by a climate rule of thumb (30 BTU per sq ft in warm areas, 40 in mixed and 50 in cold climates), keeping the result between 40,000 and 140,000 BTU.
| Living area | Warm | Mixed | Cold |
|---|---|---|---|
| 1,000 sq ft | 40,000 BTU · $3,200 – $6,900 | 40,000 BTU · $3,200 – $6,900 | 50,000 BTU · $3,300 – $7,300 |
| 1,500 sq ft | 45,000 BTU · $3,200 – $7,100 | 60,000 BTU · $3,500 – $7,700 | 75,000 BTU · $3,700 – $8,300 |
| 2,000 sq ft | 60,000 BTU · $3,500 – $7,700 | 80,000 BTU · $3,800 – $8,500 | 100,000 BTU · $4,100 – $9,300 |
| 2,500 sq ft | 75,000 BTU · $3,700 – $8,300 | 100,000 BTU · $4,100 – $9,300 | 125,000 BTU · $4,400 – $10,300 |
| 3,000 sq ft | 90,000 BTU · $3,900 – $8,900 | 120,000 BTU · $4,400 – $10,100 | 140,000 BTU · $4,700 – $10,900 |
Efficiency (AFUE)
AFUE is the share of fuel a furnace turns into heat. A standard furnace is about 80% efficient; a condensing furnace reaches 95% to 98.5%. High-efficiency furnaces typically cost $1,000 to $2,500 more and usually need new PVC venting and a condensate drain, but they burn noticeably less fuel in cold climates. Electric furnaces are already close to 100% efficient, so this choice doesn’t change their price.
Zip code
Your zip code sets a regional price factor for labor and demand.
Furnace replacement cost by region
| Region | Price factor | 80,000 BTU gas furnace, standard | Typical |
|---|---|---|---|
| Southeast (GA, SC, NC, AL, MS, TN, KY, VA, WV) | 0.88 | $3,300 – $7,500 | $5,400 |
| South Central (TX, OK, LA, AR) | 0.90 | $3,400 – $7,700 | $5,500 |
| Midwest and Mountain West | 1.00 | $3,800 – $8,500 | $6,100 |
| Mid-Atlantic (NY, NJ, PA, MD, DE, DC) | 1.15 | $4,300 – $9,700 | $7,000 |
| New England | 1.20 | $4,500 – $10,100 | $7,300 |
| Florida | 1.20 | $4,500 – $10,100 | $7,300 |
| Pacific (CA, WA, OR, AK, HI) | 1.25 | $4,700 – $10,600 | $7,600 |
Worked examples: three real-world homes
These are example homes, not real customers. Each uses national average prices (price factor 1.0).
Example 1: 1,200 sq ft home, warm climate, gas
Natural gas, standard efficiency (80% AFUE).
- Size: 1,200 sq ft × 30 BTU = 36,000 BTU; the calculator’s minimum is 40,000 BTU
- Furnace, low: $2,500 + $15 × 40 = $3,100; high: $5,000 + $40 × 40 = $6,600
- Add permit: $3,100 + $50 = $3,150 low; $6,600 + $300 = $6,900 high
- Round to the nearest $100
Estimated cost: $3,200 – $6,900 (typical $5,000)
Example 2: 2,000 sq ft home, high-efficiency gas
Mixed climate, 95%+ AFUE condensing furnace.
- Size: 2,000 × 40 = 80,000 BTU
- Furnace, low: $2,500 + $15 × 80 = $3,700, + $1,000 high-efficiency = $4,700
- Furnace, high: $5,000 + $40 × 80 = $8,200, + $2,500 = $10,700
- Add permit: $4,750 low; $11,000 high, rounded
Estimated cost: $4,800 – $11,000 (typical $7,900)
Example 3: 2,800 sq ft home, cold climate, oil
Oil furnace, standard efficiency, existing tank kept.
- Size: 2,800 × 50 = 140,000 BTU (the calculator’s maximum)
- Furnace, low: $5,000 + $20 × 140 = $7,800; high: $7,500 + $35 × 140 = $12,400
- Add permit: $7,850 low; $12,700 high, rounded
Estimated cost: $7,900 – $12,700 (typical $10,300)
Hidden costs to budget for
- Venting changes. Switching to a condensing furnace usually means new PVC vent pipes and a condensate drain; sometimes the old chimney needs a liner for the water heater left behind.
- Gas or oil line work. New piping runs about $9 to $27 per linear foot.
- A new oil or propane tank, $600 to $2,500.
- Ductwork repairs, $5 to $45 per linear foot, or $1,400 to $6,000 to replace.
- A new circuit for an electric furnace, about $175 to $500.
- Permit. Usually $50 to $300, though a few cities charge much more.
- Thermostat and air quality add-ons such as a smart thermostat or media filter.
DIY vs hiring a pro
A furnace swap isn’t a safe DIY job. Gas connections, venting and combustion testing have to be right, or the furnace can leak gas or carbon monoxide. Most areas require a licensed contractor and a permit, and manufacturers require professional installation for the warranty. Homeowners can safely change filters, keep the area around the furnace clear and book an annual tune-up ($70 to $300).
Safety: never work on gas lines or venting yourself. Install carbon monoxide alarms on every floor, and call your gas utility right away if you smell gas.
How to read a furnace quote
- Brand, model number, BTU output and AFUE rating
- How the size was worked out (ask for a Manual J load calculation)
- Venting: reused, relined or new PVC
- Gas or oil line changes, and a new tank if needed
- Condensate drain or pump for high-efficiency models
- Ductwork connections, filter rack and thermostat
- Permit, haul-away and startup combustion testing
- Parts and labor warranties
Red flags:
- A furnace sized by matching the old one without checking the house
- No combustion or carbon monoxide test at startup
- Venting left out of a high-efficiency quote
- A “condemned” furnace notice with no photos or explanation
- Cash-only pricing or no license number
Repair or replace your furnace?
| Repair is usually enough if… | Replace if… |
|---|---|
| The furnace is under about 15 years old | It is 15 to 20 years old or more |
| The part is an igniter, flame sensor or thermostat ($80 to $450) | The heat exchanger is cracked ($500 to $3,500 to fix) |
| It heats evenly once fixed | Rooms heat unevenly or it short-cycles |
| Repairs are rare | You are paying for repairs every winter |
Most furnace repairs cost $100 to $1,200 for gas and propane, $50 to $300 for electric and $400 to $1,500 for oil. Choose “repair” in the calculator for your fuel’s range.
Ways to save on a new furnace
- Replace before it fails. Emergency winter replacements leave little time to compare quotes.
- Book in spring or early fall, when contractors are less busy.
- Don’t oversize. A right-sized furnace costs less and runs more evenly.
- Pick efficiency for your climate. A 95%+ furnace pays back fastest where winters are long and cold.
- Ask about utility rebates for high-efficiency gas furnaces.
- Consider a heat pump if you also need a new AC.
Tax credit note: the federal 25C energy-efficiency credit ended for equipment installed after December 31, 2025, so it no longer applies to new furnaces. Check your gas utility and state for rebates.
Get local quotes to confirm your estimate
A heating contractor will check your venting, gas line and ducts before giving a firm price. Use the calculator above to request up to three free quotes, with no obligation. More heating and cooling prices: Heating & Cooling.
Furnace replacement FAQs
About $3,800 – $8,500 installed for a standard 80,000 BTU model at national average prices. A high-efficiency model adds about $1,000 to $2,500.
Typically 15 to 20 years with yearly maintenance.
A rough rule is 30 to 50 BTU per sq ft depending on climate, so a 2,000 sq ft home in a mixed climate needs about 80,000 BTU. A Manual J load calculation gives the right answer for your home.
In cold climates with long winters, usually yes. In mild climates, the fuel savings may not cover the extra $1,000 to $2,500.
Usually 4 to 10 hours for a like-for-like swap. Venting or gas line changes can add time.
If you also need cooling, or you heat with oil, propane or electricity, a heat pump may cost less to run. Compare prices with the heat pump cost calculator.
How we estimate these costs
ImprovementCalc prices a furnace replacement as a fixed amount by fuel plus an amount per 1,000 BTU, adding a flat amount for a high-efficiency model (gas, propane and oil only). Size comes from living area and a climate rule of thumb, limited to 40,000–140,000 BTU. Removal of the old furnace is included; tanks, line changes and ductwork are not. The permit is a separate $50–$300 line that isn’t adjusted by region. Totals are rounded to the nearest $100.
Sources:
- Fixr: Furnace Installation Cost (updated January 2026)
- Bryant: Furnace Replacement Cost
- Inch Calculator: Furnace Repair Cost
- Trane: 2023 DOE efficiency standards
Prices last checked November 2026.
Our full method: How ImprovementCalc estimates costs Where our prices come from How we test every calculator