Most homeowners pay $7,600 to $16,500 to replace an asphalt shingle roof, and about $13,300 for a typical 2,000 sq ft roof in architectural shingles. Metal, tile and slate roofs usually run $16,000 to $60,000 or more.
Use the roof replacement cost calculator below to price your own roof by home size, pitch, stories, material and zip code. Every number on this page comes from the same formula the calculator uses, so you can check the math yourself.
Roof Replacement Cost Calculator
Estimated roof replacement cost
$12,400 – $20,200
Typical: $16,300
Using national average prices. Add your zip code for local prices.
- Roof area2,460 sq ft (24.6 squares)
- New roof, installed (incl. tear-off and disposal)$12,300 – $19,700
- Permit$100 – $500
- Rotted roof deck is only found after tear-off. Budget $75–$160 per 4×8 sheet.
- Add 10–15% contingency for surprises, more on older homes or roofs with two layers.
Sorry, we couldn't calculate that. Please check your answers, or reload the page.
Compare quotes from local roofers
Free, with no obligation. Local, pre-screened pros will contact you to confirm your project and give you a price.
Thanks! Your request is in. Local pros will contact you shortly, usually within a business day, to talk about your project.
Check your quote
We compare it with the estimate for your answers above and your zip code.
Estimates are a guide. Prices vary with your home and local conditions.
Got more than one quote? Compare them side by side →
Questions to ask
Red flags
Share your price
Tell us what you were quoted or paid. We use it, anonymously, to check and improve our estimates. It uses your answers above, so change them there if you need to.
Thank you. Your price helps other homeowners.
Estimates are a guide. Prices vary with your home and local conditions.
What drives the cost of a new roof
Roofers price by the square, which is 100 sq ft of roof surface. A typical house has a roof of 15 to 30 squares. The calculator works out your roof area, multiplies it by an installed price per square foot for your material, then adjusts for how hard the job is and where you live. Here is what each answer changes, in the same order as the calculator.
Roof size
Size matters more than anything else. If you know your roof area (from a past quote, an insurance report or a satellite measurement), enter it directly. If not, the calculator estimates it from your home’s living area: it divides by the number of stories to get the footprint, multiplies by a pitch factor because a sloped roof has more surface than the floor under it, and adds 10% for overhangs (the eaves that stick out past the walls).
| Home living area | 1-story home: roof area | 2-story home: roof area |
|---|---|---|
| 1,000 sq ft | 1,230 sq ft (12.3 squares) | 615 sq ft (6.1 squares) |
| 1,500 sq ft | 1,845 sq ft (18.4 squares) | 922 sq ft (9.2 squares) |
| 2,000 sq ft | 2,460 sq ft (24.6 squares) | 1,230 sq ft (12.3 squares) |
| 2,500 sq ft | 3,075 sq ft (30.7 squares) | 1,537 sq ft (15.4 squares) |
| 3,000 sq ft | 3,689 sq ft (36.9 squares) | 1,845 sq ft (18.4 squares) |
Stories
A two-story home has half the footprint of a one-story home with the same living space, so it has a smaller roof. That’s why the calculator divides by stories. Height still costs money, though: crews need taller ladders, more fall protection and more time hauling materials up. For homes of three or more stories, the calculator adds 10% to labor and materials.
Roof pitch
Pitch is how steep your roof is, written as inches of rise per 12 inches of run. A 6/12 roof climbs 6 inches for every foot across. Steeper roofs have more surface area, and above about 8/12 roofers can’t walk the roof safely without roof jacks and harnesses, which slows the job.
| Pitch | Area factor | Difficulty surcharge | 2,000 sq ft one-story home, architectural shingles |
|---|---|---|---|
| Low (up to 4/12) | × 1.054 | None | $11,700 – $19,100 |
| Medium (5/12 to 7/12) | × 1.118 | None | $12,400 – $20,200 |
| Steep (8/12 to 9/12) | × 1.25 | +20% | $16,600 – $26,900 |
| Very steep (10/12 or more) | × 1.302 | +30% | $18,700 – $30,300 |
Roof material
Material sets the price per square foot. The rates below are installed prices: shingles or panels, underlayment, flashing, labor, and tear-off and disposal of one old layer of asphalt shingles. They are national averages before regional adjustment.
| Material | Installed cost per sq ft | 2,000 sq ft roof (with permit) | Typical lifespan |
|---|---|---|---|
| 3-tab asphalt shingles | $4 – $6 | $8,100 – $12,500 | 15 – 20 years |
| Architectural asphalt shingles | $5 – $8 | $10,100 – $16,500 | 25 – 30 years |
| Premium/designer asphalt shingles | $8 – $12 | $16,100 – $24,500 | 30+ years |
| Flat roof (modified bitumen, EPDM, TPO) | $4 – $14 | $8,100 – $28,500 | 15 – 30 years |
| Metal, exposed-fastener panels | $7 – $12 | $14,100 – $24,500 | 25 – 40 years |
| Metal, standing seam | $10 – $18 | $20,100 – $36,500 | 40 – 70 years |
| Concrete tile | $8 – $14 | $16,100 – $28,500 | 40 – 50 years |
| Wood shake | $8 – $15 | $16,100 – $30,500 | 30 – 50 years |
| Clay tile | $10 – $20 | $20,100 – $40,500 | 50 – 100 years |
| Natural slate | $15 – $30 | $30,100 – $60,500 | 75 – 100+ years |
Architectural shingles (also called dimensional or laminated shingles) are the default on most US homes now. They are thicker than 3-tab shingles, look better, and usually carry a longer warranty for only about $1 to $2 more per sq ft. Standing seam metal uses concealed fasteners and raised seams, so it lasts longer and leaks less than cheaper exposed-fastener panels.
Old roof layers to remove
The material rates above already include tearing off one layer of shingles. A second layer means twice the weight to strip and haul away, so the calculator adds $1 to $2 per sq ft. Building codes don’t allow a new roof over two existing layers, so a two-layer roof always needs a full tear-off. If there’s nothing to remove (a new build or bare deck), the calculator takes $1 to $1.50 per sq ft off.
| Layers to remove | Price change per sq ft | 2,000 sq ft roof, architectural shingles |
|---|---|---|
| None (new build or bare deck) | −$1.00 to −$1.50 | $8,100 – $13,500 |
| 1 layer (included) | $0 | $10,100 – $16,500 |
| 2 or more layers | +$1.00 to +$2.00 | $12,100 – $20,500 |
Job type
Replacing a roof, roofing a new build or addition, and roofing a detached garage or shed are priced the same way per square foot. The answer mostly helps us match you with the right kind of roofer if you ask for quotes. Small garage and shed roofs often cost more per square foot than the calculator shows, because many roofers have a minimum job charge.
Zip code
Your zip code sets a regional price factor, because labor rates, building codes and demand vary a lot across the country. Roofer wages differ widely between states, and coastal states with wind codes, like Florida, need extra nailing, underlayment and inspections.
Roof replacement cost by size and region
Cost by roof size
| Roof area | Squares | Architectural asphalt | Standing seam metal |
|---|---|---|---|
| 1,000 sq ft | 10 | $5,100 – $8,500 | $10,100 – $18,500 |
| 1,500 sq ft | 15 | $7,600 – $12,500 | $15,100 – $27,500 |
| 2,000 sq ft | 20 | $10,100 – $16,500 | $20,100 – $36,500 |
| 2,500 sq ft | 25 | $12,600 – $20,500 | $25,100 – $45,500 |
| 3,000 sq ft | 30 | $15,100 – $24,500 | $30,100 – $54,500 |
Cost by region
| Region | Price factor | 2,000 sq ft roof, architectural shingles | Typical |
|---|---|---|---|
| Southeast (GA, SC, NC, AL, MS, TN, KY, VA, WV) | 0.88 | $8,900 – $14,600 | $11,700 |
| South Central (TX, OK, LA, AR) | 0.90 | $9,100 – $14,900 | $12,000 |
| Midwest | 1.00 | $10,100 – $16,500 | $13,300 |
| Mountain West (CO, UT, AZ, NV, ID, MT, WY, NM) | 1.00 | $10,100 – $16,500 | $13,300 |
| Mid-Atlantic (NY, NJ, PA, MD, DE, DC) | 1.15 | $11,600 – $18,900 | $15,300 |
| New England | 1.20 | $12,100 – $19,700 | $15,900 |
| Florida | 1.20 | $12,100 – $19,700 | $15,900 |
| Pacific (CA, WA, OR, AK, HI) | 1.25 | $12,600 – $20,500 | $16,600 |
Worked examples: three real-world roofs
These are example homes, not real customers. Each one uses national average prices (price factor 1.0) so you can follow the math. Your zip code moves the roof cost up or down by your region’s factor.
Example 1: 1,200 sq ft ranch, architectural shingles
One story, low pitch (4/12), one layer of old shingles.
- Roof area: 1,200 sq ft ÷ 1 story × 1.054 (pitch) × 1.1 (overhangs) = 1,391.3 sq ft (13.9 squares)
- Roof, low: 1,391.3 sq ft × $5 = $6,956
- Roof, high: 1,391.3 sq ft × $8 = $11,130
- Add permit: $6,956 + $100 = $7,056 low; $11,130 + $500 = $11,630 high
- Round to the nearest $100
Estimated cost: $7,100 – $11,600 (typical $9,300)
Example 2: 2,400 sq ft two-story, two layers to remove
Two stories, medium pitch (6/12), architectural shingles, two old layers that both have to come off.
- Footprint: 2,400 sq ft ÷ 2 stories = 1,200 sq ft
- Roof area: 1,200 × 1.118 (pitch) × 1.1 (overhangs) = 1,475.8 sq ft (14.8 squares)
- Rate with the extra layer: $5 + $1 = $6 low; $8 + $2 = $10 high per sq ft
- Roof: 1,475.8 × $6 = $8,855 low; 1,475.8 × $10 = $14,758 high
- Add permit: $8,955 low; $15,258 high, rounded to the nearest $100
Estimated cost: $9,000 – $15,300 (typical $12,100)
Example 3: 3,600 sq ft two-story, steep standing seam metal
Two stories, steep pitch (9/12), switching to standing seam metal, one layer of old shingles.
- Footprint: 3,600 sq ft ÷ 2 stories = 1,800 sq ft
- Roof area: 1,800 × 1.25 (steep pitch) × 1.1 (overhangs) = 2,475 sq ft (24.8 squares)
- Steep-roof surcharge for harnesses, roof jacks and slower work: × 1.2
- Roof: 2,475 × $10 × 1.2 = $29,700 low; 2,475 × $18 × 1.2 = $53,460 high
- Add permit: $29,800 low; $53,960 high, rounded to the nearest $100
Estimated cost: $29,800 – $54,000 (typical $41,900)
Hidden costs to budget for
A roof quote can grow once the old shingles come off. Set aside 10% to 15% as a contingency, and more on an older home or a roof with two layers.
- Rotted roof deck. The plywood or OSB under your shingles can only be checked after tear-off. Replacing a 4×8 sheet typically costs $75 to $160 installed. Get the per-sheet price written into your contract before work starts.
- Permit. Most towns require a reroofing permit. Many charge $100 to $500, but cities that charge by project value can ask for more on an expensive roof.
- Flashing and pipe boots. The metal around chimneys, walls and skylights, and the rubber collars around vent pipes, should be replaced, not reused. Check that the quote says so.
- Ventilation. Poor attic ventilation shortens shingle life and can void the warranty. Adding ridge or soffit vents is a common add-on.
- Ice and water shield and drip edge. Many codes require them along eaves and valleys, especially in snowy areas. They are sometimes left off low quotes.
- Gutters. Old gutters often get bent during tear-off or don’t line up with the new drip edge.
- Structural upgrades. Switching to heavy tile or slate may need extra framing. Changing roofs in hurricane zones can require upgraded nailing or straps.
- Access. Steep driveways, tight lots, landscaping protection and no room for a dumpster all add time and cost.
DIY vs hiring a roofer
Reroofing is one of the riskiest home projects to do yourself. Federal OSHA rules require professional roofing crews to use fall protection whenever they work 6 feet or more above a lower level, because a fall from a roof can be fatal. A full tear-off also means lifting thousands of pounds of shingles, working against the weather, and leaving your home open to rain if the job runs long.
Safety first: don’t climb onto a steep, wet or two-story roof without proper fall protection. Hire a licensed, insured roofer for tear-off and installation, and for any work near power lines.
What an average DIYer can safely do: measure the house footprint, photograph damage from the ground or a ladder at the eaves, clear the attic and move cars and patio furniture before the crew arrives, and handle the paperwork for insurance claims. These won’t lower the quote much, but they speed the job up and help you compare quotes.
Where DIY goes wrong: leaks at flashing and valleys, wrong nailing patterns that fail in high wind, and lost warranties. Shingle manufacturers’ extended warranties usually require installation by a contractor they have certified. A small garage or shed roof with a low pitch is the one place a skilled DIYer might save the labor, which is a big part of every roofing quote.
How to read a roofing quote
Get at least three written quotes, and make sure each one prices the same job. A good quote itemizes:
- Roof size in squares, and how it was measured
- Shingle or panel brand, product line and color
- Tear-off: how many layers, and disposal
- Underlayment type, ice and water shield, and drip edge
- New flashing, pipe boots and vents
- Price per sheet for any rotted decking
- Permit, and who pulls it
- Start date, cleanup (including magnetic nail sweep) and payment schedule
- Workmanship warranty from the roofer, separate from the manufacturer’s warranty
Questions to ask: Are you licensed and insured in this state (ask for certificates)? Will you replace all flashing? Who is the crew, and are they your employees or subcontractors? What happens if it rains mid-job?
Red flags:
- A large cash deposit before materials arrive
- Door-to-door “storm chasers” who show up right after hail or wind
- An offer to “cover” or waive your insurance deductible, which is illegal in some states
- One lump-sum price with no breakdown
- No written per-sheet price for decking
- No local address, license number or proof of insurance
Repair or replace your roof?
Repair makes sense when the damage is limited and the roof has life left. Replacement makes sense when you would be patching a roof that is near the end anyway.
| Repair is usually enough if… | Replace if… |
|---|---|
| The roof is less than about 15 years old (asphalt) | Asphalt shingles are 20 to 25+ years old |
| There is one leak with a clear cause, like a cracked pipe boot or loose flashing | You have leaks in several places, or leaks keep coming back |
| A few shingles blew off in a storm | Damage covers about a third of the roof or more |
| Granule loss and curling are limited to one slope | Shingles are curling, cracked or bald across the roof |
| The deck is solid | The deck sags or feels soft underfoot |
Insurance can change the math. If a storm damaged your roof, your policy may pay for a full replacement, minus your deductible. Older roofs are often paid at actual cash value (after depreciation), not replacement cost, so read your policy before you decide.
Ways to save on a new roof
- Compare three or more quotes for the same scope. Prices for an identical roof often differ by thousands.
- Pick architectural shingles over premium designer lines unless you need the look. They usually give the best cost per year of life.
- Book outside peak season. Roofers are busiest in summer and right after big storms. Late fall and early spring can bring better scheduling and sometimes better prices, where the weather allows.
- Lock in the decking price per sheet before work starts, so surprises don’t become expensive.
- Fix ventilation at the same time. It costs less while the roof is open and protects your warranty.
- Look for state and insurer programs. Some states offer grants or insurance discounts for storm-resistant roofs built to the IBHS FORTIFIED standard, such as the Strengthen Alabama Homes program.
Tax credit note: the federal 25C energy-efficiency credit ended for work completed after December 31, 2025, so don’t count on a federal tax credit for a 2026 roof. Check your state, utility and insurer for current programs instead.
Get local quotes to confirm your estimate
Your estimate is a starting point. Local roofers can measure your roof, check the deck and give you a firm price. Use the calculator above to request up to three free quotes, with no obligation.
Related: Roofing costs · Gutter installation cost calculator · Siding cost calculator · Solar panel cost and payback calculator · Insulation cost calculator
Roof replacement FAQs
For a one-story 2,000 sq ft home with a medium-pitch roof, the roof is about 2,460 sq ft, and architectural shingles cost about $12,400 to $20,200 at national average prices. A two-story home with the same living area has a roof half that size, so it costs about $6,200 to $10,300.
Divide your roof area in square feet by 100. If you only know your living area, divide it by the number of stories, then multiply by about 1.23 for a medium-pitch roof with overhangs. A 2,000 sq ft one-story home has a roof of about 24 to 25 squares.
Sometimes, if there is only one layer and the deck is sound. Codes don’t allow a new roof over two existing layers. An overlay saves tear-off costs, but it hides deck problems, adds weight and can shorten the new roof’s life, so most roofers recommend a full tear-off.
Most asphalt shingle roofs on a typical home take one to three days. Steep, complex or large roofs, metal, tile and slate take longer, and bad weather can add days.
Insurance usually pays when a covered event, like hail or wind, damaged the roof. It doesn’t pay for old age or wear. You pay your deductible, and older roofs may only be paid at depreciated value.
Yes, but you won’t get all of it back. The 2025 Cost vs. Value report estimated an asphalt roof replacement recoups about 67.5% of its cost at resale, and a metal roof about 50%. A new roof also makes a home easier to sell and insure.
Standing seam metal costs about twice as much as architectural shingles, but it can last 40 to 70 years versus 25 to 30. If you plan to stay in the home a long time, metal can cost less per year of life.
How we estimate roof costs
ImprovementCalc’s roof estimates use installed price ranges per square foot by material, cross-checked against several national cost guides published or updated in 2025 and 2026. Our rates include tear-off and disposal of one layer of shingles. Roof area comes from living area, stories, a standard pitch factor and a 10% overhang allowance. Steep and three-story roofs get a difficulty surcharge. Regional factors reflect differences in labor rates, building codes and demand. The permit is a separate $100–$500 line and isn’t adjusted by region. Totals are rounded to the nearest $100. Actual quotes depend on your roof’s condition, complexity and local market.
Sources:
- This Old House: How Much Does a New Roof Cost? (updated October 2026)
- Fixr: Asphalt Shingle Roofing Cost (updated January 2026)
- Fixr: Slate Roof Cost (updated January 2026)
- This Old House: Standing Seam Metal Roof Cost (updated March 2026)
- This Old House: Tile Roof Cost (updated April 2026)
- HomeAdvisor: Roof Replacement Cost and Flat Roof Replacement Cost
- Inch Calculator: Cost to Replace a Roof (tear-off and labor per square)
- LatestCost: Roof Plywood Replacement Cost (decking per sheet)
- Example municipal reroofing permit fee schedule (Bay City, MI)
- JLC Cost vs. Value 2025: national data
- OSHA residential fall protection, 29 CFR 1926.501(b)(13)
- Strengthen Alabama Homes 2026 program rules
Prices last checked November 2026.
Our full method: How ImprovementCalc estimates costs Where our prices come from How we test every calculator